Next Article in Journal
Water Resource Management through the Lens of Planetary Health Approach
Next Article in Special Issue
Potential Analysis of Atmospheric Water Harvesting Technologies from the Perspective of “Trading-in Energy for Water”
Previous Article in Journal
Stormwater Management in Urban and Rural Areas
Previous Article in Special Issue
Radar Quantitative Precipitation Estimation Algorithm Based on Precipitation Classification and Dynamical Z-R Relationship
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Water
Volume 14
Issue 21
10.3390/w14213487
water-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Review

Atmospheric Water Harvesting with Metal-Organic Frameworks and Their Composites: From Materials to Devices

by
Xiuying Huang
1,
Qin Qin
2,
Qinglang Ma
1,* and
Bo Wang
1,*
1
Frontiers Science Center for High Energy Material, Beijing Key Laboratory of Photoelectronic/Electrophotonic Conversion Materials, Key Laboratory of Cluster Science, Ministry of Education, Advanced Research Institute of Multidisciplinary Science, School of Chemistry and Chemical Engineering, Beijing Institute of Technology, Beijing 100081, China
2
Chongqing Advanced Materials Institute, Chongqing 408107, China
*
Authors to whom correspondence should be addressed.
Water 2022, 14(21), 3487; https://doi.org/10.3390/w14213487
Submission received: 27 September 2022 / Revised: 18 October 2022 / Accepted: 21 October 2022 / Published: 1 November 2022
(This article belongs to the Special Issue Atmospheric Water Resources Exploitation and Utilization)
Browse Figures
Versions Notes

Abstract

:
Clean water scarcity is deteriorating because of the growing population and water pollution. New methods to harvest freshwater from non-traditional water sources are urgently required to address this global issue. The atmosphere contains abundant water resources. Harvesting fresh water from the air has become an emerging and attractive approach, among which sorption-based atmospheric water harvesting (AWH) is the most promising method, as it demonstrates high water producibility, wide applicability and low energy consumption. Metal-organic frameworks (MOF) are a class of emerging porous materials characterized by their large specific surface area, adjustable pore structures and chemistry. Recently, hydrolytically stable MOFs have been used as sorbents in AWH, and several MOF-based prototyping devices have been demonstrated with great practical potential. In this review, we briefly summarize the recent progress on the MOFs and their derived composites as AWH sorbents. Then, we introduce several most representative devices using MOFs for practical applications. Finally, the challenges and perspectives of this emerging field are discussed.

1. Introduction

Water is the source of life and a critical resource for social development. Although Earth is an enormous reservoir of water with 1.3 billion cubic kilometers in quantity, only 3% of which is freshwater [1]. However, most freshwater exists in the form of glaciers and underground water, leaving only 0.3% of the total freshwater available for direct utilization [2]. It is reported that two-thirds of the global population, i.e., around 4 billion people, live with severe water shortages [3]. The growing global population and the deteriorating water pollution put further pressure on the water shortage problem. To address water scarcity, novel materials and technologies are developed and implemented to extract freshwater from unconventional water sources, such as seawater, wastewater, and rain. However, these technologies, including seawater desalination [4,5,6], industrial wastewater purification [7,8], etc., are extremely energy-intensive and often require large-footprint infrastructures, thus only suitable for large cities with centralized water and electricity supply system. Unfortunately, regions where freshwater is scarce are often short of electricity supplies, and the land space is limited, such as deserts, islands, and remote rural areas [6]. Therefore, the prevailing technologies for centralized clean water supply are not suitable for these remote areas.
There is an urgent need to develop other decentralized water supply methods that can harvest fresh water from alternative water sources in an energy-saving and small-scale manner to satisfy the needs of these regions. The atmosphere contains a tremendous amount of water in the form of molecular vapor and small droplets. The total atmospheric water content is estimated to be 13,000 trillion liters, about six times as much water as rivers and lakes [9], which is enough to satisfy the drinking and agricultural needs of the world [10]. Harvesting freshwater from the atmosphere is thus a promising method to provide water for remote areas without centralized infrastructures, where both natural surface water sources and electricity are scarce.
Generally, there are three approaches for atmospheric water harvesting, i.e., fog harvesting, dew collection driven by chillers, and sorption-based AWH (SBAWH). Fog is formed by micro-sized water droplets suspended in the atmosphere. These droplets tend to grow in size, driven by their surface tension, until they are large enough to be separated and collected by gravity [11]. A fog trap net can be used to capture the small water droplets floating in the air by favoring the growth of the water droplets, after which the gathered water is available for utilization [12,13,14]. Fog collection from the air has been put into practice to supply fresh water. For example, inspired by the Namib Desert beetle’s shell that can collect water droplets from fog, researchers designed and fabricated devices for fog capture. These devices have been practically implemented in the coastal mountains on the edge of the Atacama Desert in northern Chile [15]. However, this method requires a local environment with near 100% relative humidity (RH) to be effective. Such stringent requirement seriously limits its practical application only to coastal and hilly areas [16]. Dew collection involves a phase change process where the vapor molecules of water transform to aqueous water when the air is cooled below its dew point, i.e., the temperature at which the water vapor is saturated. The cooling process generally consumes large amounts of energy to overcome sensible heat and latent heat of water during condensation [17,18]. Moreover, the efficiency and applicability of dew collecting depend on seasons and regions because the dew point varies with the temperature and RH of the outside environment. Such an approach is not suitable for dry and hot conditions, where the dew point can be extremely low [13].
In contrast, for the sorption-based atmospheric water harvesting approach, solid or liquid desiccants with strong hygroscopicity are used to gather the moisture from the air spontaneously and then desorb the vapor with a temperature or pressure swing [19]. The released water vapor condenses back to aqueous water in a confined space with high local humidity and is collected for usage (Figure 1). Compared to dew collection, the critical advantage of sorption-based AWH is that it greatly increases the dew point by creating a high local humidity environment in the vicinity of the sorbent. Thus, this approach is applicable even in arid regions and greatly reduces energy consumption. Solar energy and even low-grade waste heat are possible to drive the desorption of the water molecules from the desiccants. Therefore, sorption-based AWH is the most promising approach for decentralized water supply, especially in low-RH environments, and has attracted tremendous research attention [20,21].
The sorbent material is the core of the SBAWH approach. An ideal sorbent for AWH should have excellent hydrolytic stability, high water uptake capacity, fast sorption-desorption kinetics, and low regeneration temperature. So far, several porous solids and hygroscopic salts have been studied and implemented under certain practical conditions. For example, silica gels can attract water molecules with their abundant polar hydroxyl groups by the formation of hydrogen bonds, and they are widely and commercially used desiccants due to their non-toxicity, commercial availability, and facile regeneration [22]. Nevertheless, their water production performance is limited by the low sorption capacity [23]. Zeolites are another classical desiccant that shows high water uptake capacity and fast sorption kinetics due to their porous structures. They can adsorb water molecules even at extremely low RH because the open metal sites bind strongly with water molecules [24,25]. However, the strong affinity toward water molecules makes the regeneration of zeolites difficult and energy-intensive [26]. In contrast to the physical adsorption process by the silica gel and zeolites, hygroscopic salts, e.g., LiCl and CaCl2, capture moisture by a rapid chemical hydration process [27]. Hygroscopic salts show the highest water uptake capacity among all common desiccants, as they can continuously absorb water until salt particles dissolve in the captured water and form liquid absorbent, which continues to absorb moisture, i.e., the deliquescence process [28,29]. However, the deliquescent characteristics of the salts will lead to the contamination of collected water by the salt ions, which could also result in the corrosion of devices. Moreover, the repeated dissolution and precipitation of the salts can result in a change in particle size and morphology, limiting their long-term cycling performance. Therefore, designing and synthesizing novel sorbent materials with the desirable water sorption and desorption characteristics is still of great significance.
Metal-organic frameworks (MOFs) are a kind of crystalline porous materials with well-defined intramolecular pores formed by the organic ligands and metal ions or clusters [30,31]. Owing to the intriguing properties of their rich and tunable pore structures and chemistry, MOFs have shown promising potential in a wide range of applications, such as gas storage, molecular separation, and catalysis [32,33,34,35]. The ultrahigh porosity of MOFs makes them ideal candidates for water adsorption, evidenced by the step-shaped isotherm profiles of many MOFs. A Step-shaped water adsorption isotherm indicates that water can be uptake and released in a relatively small temperature and pressure difference, potentially leading to an energy-efficient ad-/desorption process. Therefore, MOF is believed to be the most promising material for SBAWH and has attracted increasing research attention. Furthermore, their tunable surface chemistry made it possible to composite with various other materials to bring more synergy and multi-functionalities to SBAWH.
In this review, we will briefly introduce the materials and devices for SBAWH based on MOFs and MOF-based composites. First, we will overview water-adsorbing MOFs and discuss their performance with different water adsorption mechanisms. Then, we will introduce some MOF-based composites by highlighting their integration among individual advantages of MOFs and other functional elements. Next, devices for SBAWH will be introduced to map out their potential engineering designs toward practical applications. Finally, we will discuss the remaining challenges and future directions in terms of both material and device aspects. We hope this review could stimulate more research interest in this important and emerging research field.

2. MOFs for Sorption-Based AWH

The chemical and structural stability of MOFs in the presence of water is the fundamental request for them to be usable as AWH sorbents. Although most MOFs collapse upon exposure to water, recent research has demonstrated many hydrolytically stable MOFs by the proper choice of metals and ligands. Generally, secondary building units (SBU) with high connectivity, strong metal-ligand bonds, and hydrophobic ligands could result in MOF with high water stability. For example, M6O8-type (M = Zr4+, Hf4+) and M3O-type (M = Al3+, Fe3+) SBU with pyrazole- and carboxylate-based ligands have demonstrated excellent hydrolytic stability, such as UIO-66 and MIL-101. A host of hydrothermally stable metal-organic frameworks have been studied as potential sorbents for SBAWH applications [36,37,38,39,40,41]. Table 1 provides a summary of representative MOFs and their critical parameters, including the inflection point and the saturated uptake capacity, in AWH’s application.
The water vapor adsorption by MOFs follows three mechanisms: (1) chemisorption on open metal sites, (2) pore-filling process by water cluster formation, and (3) capillary condensation. The most typical example of chemisorption on open metal sites is studied with the (M)MOF-74 (M = Mg2+, Zn2+, Ni2+, Co2+) series. (M)MOF-74 crystals have one-dimensional hexagonal-shaped pores formed by helical chains of octahedron SUBs linked to linear DOT (2,5-dihydroxy-terephthalic acid) ligands. One oxygen in each SBU is from coordinating water, which residues toward the center of the hexagonal pore. The coordination water can be removed upon activation, leaving an unsaturated metal site, which was proved by DFT calculations on (Mg)MOF-74 (inset picture of Figure 2a) [50]. X-ray diffraction (XRD) characterizations on hydrated (Zn)MOF-74 showed the presence of three water absorption sites of various strengths, represented by three different sizes of thermal ellipsoids, which can indicate the magnitudes and directions of the thermal vibration [51,52]. In Figure 2a, the unoccupied coordination sites of the Zn atoms attract water molecules and bind them tightly by chemisorption, reflected by the smallest ellipsoids. The water molecules near the SBUs are physically absorbed, and they have larger ellipsoids, and the largest ones represent the loosely bound water molecules in the pore center. The adsorption isotherms of the MOF-74 series have the initial steep slope shown in Figure 2b, which is due to the chemisorption on metal sites of water molecules. Water molecules are absorbed tightly so that the sorbents need high thermal energy to regenerate, which is undesirable for sorption-based AWH applications.
The pore-filling process that is often adopted by microporous MOFs involves two steps. First, water molecules are adsorbed on the primary sites of the pores, usually polar and hydrophilic centers. Then, these adsorbed water molecules can act as secondary sorption sites to adsorb other water molecules into the pores to form water clusters, leading to continuous pore filling [53]. This process has been explored on MOF-303 (Al(OH)(PZDC), PZDC2− = 1-H-pyrazole-3,5-dicarboxylate) by single-crystal XRD characterizations and DFT calculations by Yaghi and his coworkers [45]. They explained the pore-filling sequence and mechanism of MOF-303 in detail during the water uptake and desorption process and identified the exact water adsorption sites. SCXRD analysis showed that the strongest water adsorption site of the framework was located between the pyrazoles (site I in Figure 2c), where the water molecules formed three hydrogen bonds with two N(H) atoms of the PZDC2− linker and one hydroxyl group of the SBU. The second and third water molecules entering the pore channel form hydrogen bonds with two N(H) atoms of the PZDC2− linker (site II) and the remaining hydroxyl group of the SBU (site III), respectively. Then, the subsequent water molecules fill pores by forming hydrogen bonds with water molecules residing at sites I and II, forming water clusters at site IV. They fill the pores by interacting with other water molecules rather than with the framework itself. The first water molecules are attached and bound tightly with polar centers, reflecting in the isotherm as an additional step at low vapor pressure, as shown in Figure 2d. Analogously, the formation of ordered water molecule clusters was found in a zirconium-based MOF, i.e., MOF-801, by XRD and neutron diffraction characterizations [40]. The appropriate pore size makes the zirconium SBUs of MOF-801 form hydrogen bonds with water molecules to continuously adsorb water vapor from the air. MOFs adsorbing water molecules following the pore-filling mechanism have small pore volumes and thus often have small adsorption capacities. The water sorption capacity of MOF-801 and MOF-303 is both less than 0.5 g g−1.
The last mechanism is capillary condensation, which is mainly involved in mesoporous MOFs [52,54]. Owing to the large pore size, water molecules are adsorbed and condensed inside the porous channels. Reversing this process consumes more energy than the other two mechanisms. Using long organic ligands to increase the pore volume can improve the water adsorption capacity of MOFs. For example, Cr-soc-MOF-1 with ultra-high porosity has a record water adsorption capacity of 1.95 g g−1 at 70% RH (Figure 2e,f) [49]. However, the larger pore volume could lead to more energy consumption to regenerate the MOFs due to capillary condensation, reflected as the hysteresis loop in the isotherm [19,52,55].

3. MOF-Based Composites for Sorption-Based AWH

Compared to traditional desiccants, MOFs have shown advantages in sorption-based AWH in terms of low humidity performance and ideal step isotherms. However, single-component MOFs may not satisfy the practical needs as they are still limited by low water uptake capacity and energy-intensive regeneration process. Composites of MOFs with other functional materials by chemical synthesis and physical impregnation have been prepared to bring a synergistic combination of their respective merits. In this section, we will briefly discuss various types of MOF-based composites and their water sorption performance. Table 2 summarizes the characteristics of these composites.

3.1. MOF-Hydrogel Composites

Hydrogels are crosslinked networks of hydrophilic polymer chains. Due to the high flexibility of the polymer chains, hydrogels tend to swell and expand upon taking up water. Therefore, they exhibit high water storage capacity. Moreover, the wide diversity of polymer types could bring the hydrogels various additional functions. Recently, the thermal stimuli-responsive hydrogel with lower critical solution temperature (LCST) has been extensively studied. The thermo-responsive polymeric hydrogel could change its wettability by its phase change according to environmental temperature. When the outside temperature is lower than its LCST, the hydrogel is hydrophilic, and it can serve as a water reservoir at the molecular level. Once the environmental temperature is higher than its LCST, the hydrogel becomes hydrophobic, and the adsorbed water within the hydrogel will be repelled. The unique property of this kind of hydrogel is ideal for sorption-based AWH sorbents because it can ensure easy regeneration. Several MOF-hydrogel composites sorbent by combining MOFs with the thermos-responsive hydrogel, poly (N-isopropyl acrylamide) (PNIPAM) hydrogel has been reported [60,61,65]. Specifically, Karmakar et al. prepared a thermos-responsive MOF-hydrogel composite by in-situ polymerized PNIPAM hydrogel within the mesopores of MIL-101(Cr) for water capture and heat transfer applications (Figure 3a) [61]. Pure MIL-101(Cr) has a high airborne water harvesting capacity of 1.01 g g−1 at 90% RH, and it functions as the major vapor adsorbing component. After loading MIL-101(Cr) with PNIPAM, the composite can largely retain the water uptake capacity of MOFs (Figure 3b). The complete desorption and release of water from pure MIL-101(Cr) requires a high temperature of around 90 °C [66]. In sharp contrast, the MIL-101(Cr)-PNIPAM composite sorbent can release nearly all of the captured water at an unprecedentedly mild condition of around 40 °C, i.e., LCST of the confined PNIPAM, due to the hydrophilic to hydrophobic transition of PNIPAM (Figure 3c). Therefore, the desorption process of the composite is much faster and requires less energy.

3.2. MOF Complexed with Carbon-Based Materials

Due to the excellent photothermal property and thermal conductivity, carbon-based materials, such as CNTs [63,67], graphene oxide [64], carbon fiber [68], and carbon black [59], are also used to composite with MOFs, so the desorption process could be driven by natural sunlight or low-grade waste heat. For example, Li. et al. synthesized a novel nanofibrous membrane-loaded MIL-101(Cr) composite sorbent [63]. The nanofibers made of polyacrylonitrile (PAN) and CNTs were prepared by a free surface electrospinning process to form a nanofibrous membrane substrate, and MIL-101(Cr) was subsequently loaded onto the membrane by the spray coating method. The nanofibers are intertwined to form a multilayer structure with open microchannels on which the MIL-101(Cr) particles are uniformly dispersed. The MIL-101(Cr) particles are mainly responsible for moisture adsorption, while the CNTs promote rapid and complete vapor desorption upon exposure to sunlight due to their high solar light absorbance and outstanding photothermal conversion efficiency. In addition, the nanofibrous substrate fabricated by the electrospinning technique provides interconnected paths benefiting the rapid diffusion of water molecules. This composite membrane shows fast ad-/desorption kinetics compared to pure MOF sorbents, and it can desorb completely only using sunlight.
Generally, an electric heater is necessary to help desorption and release water when the natural sunlight is not sufficient or the sorbent materials suffer from low photothermal conversion capability. Carbon fiber with a high electro-thermal conversion efficiency can be used as heaters to facilitate the fast desorption of a MOF adsorbent. For example, Li et al. prepared a MOF-based composite by embedding carbon fiber bundles at the center of cylindrical Al-Fumarate adsorbent loaded within sodium alginate [68]. The inner carbon fiber is coaxially connected with the outer adsorbents, which convert electricity to thermal energy to assist the desorption of Al-Fumarate. Furthermore, graphene oxide (GO) can help to improve energy efficiency by prolonging the thermal conductivity of an electrical heater for desorption. So, loading MOF and graphene oxide are expected to promote the desorption of MOFs. Laha et al. synthesized ternary MOF-clay-graphene oxide nanocomposite, including aminopropyl clay, graphene oxide, and CuBTC (Cu3(BTC)2(H2O)3, BTC = benzene-1,3,5-tricarboxylate) through an in situ hydrothermally synthesis process for indoor sorption-based AWH [64]. The CuBTC nanoparticles uniformly grow on the non-porous two-layered templates made of aminopropyl clay and graphene oxide. Among all the components, CuBTC mainly acts as a sorbent and graphene oxide is added because of its extended heat conductivity, which will promote water release during desorption. Although CuBTC sorbent is suitable for a wide range of RH, its instability under humid conditions limits practical use. The dynamic water-dispersible characteristics of aminopropyl clay can improve the hydrolytic stability of the ternary MOF-based composite. This composite shows a water sorption capacity enhanced by 39% compared to pure CuBTC and it can achieve facile regeneration.

3.3. Salt-in-MOF Composite Sorbents

Apart from functioning as merely a desiccant, MOF could also play an important role in composite absorbents as a matrix due to their stable porous structure. As mentioned above, hygroscopic salts have a high water-sorption capacity among all conventional desiccants. However, the deliquescence of the hygroscopic salt into liquid will cause the agglomeration of salt particles during dehydration, reducing the ad-/desorption kinetics by slowing the further penetration of subsequent water molecules and eventually decreasing the overall performance. Incorporating these salts into a porous MOF matrix has been proposed to overcome this issue [69,70,71]. The matrix can provide a confined and rigid space for the deliquescence and liquefaction of the hygroscopic salt. The liquefied salt was confined within the pores of MOFs due to capillary force, which prevents the hygroscopic salt from leakage and agglomeration. Consequently, this design of structure can accelerate the ad-/desorption as the diffusion of water molecules becomes less hindered. Because of their permanent porosity, large pore volume, and large specific surface areas, MOFs are an optimal choice as a porous matrix to host salts [56,57,58,72], referred to as salt-in-MOF sorbents.
CaCl2-in-UIO-66 is one of the earliest salt-in-MOF composites to achieve adsorption-based heat transformation [58]. The spherical hollow structure of UIO-66 encapsulated CaCl2 was prepared by the spray-dry method. The robust structure of UIO-66 provides spaces for the ad-/desorption of CaCl2. The homogeneous distribution of Ca and Cl elements in the inter-particle voids of CaCl2-in-UIO-66 superstructures shows that salts can be confined in both the inherent microporosity of MOFs and the voids between MOFs (Figure 4a). These confined salts play a crucial role in increasing the water sorption capacity of composite material. This composite sorbent shows a sorption capacity of 0.67 g g−1 under 30% RH at 30 °C, which is a significant increase compared to the water absorption capacity of 0.25 g g−1 for pure UIO-66 at the same condition (Figure 4b). Recently, LiCl-in-MIL-101(Cr) has been reported to incorporate LiCl in the water-stable MIL-101(Cr) by physical impregnation (Figure 4c) [56]. The large porosity and stable pore structure of the MIL-101(Cr) matrix ensure the sorption processes of salt occurs inside of the matrix without leakage and agglomeration, thus preventing a decrease in the ad-/desorption kinetics of LiCl salts. Both LiCl and MIL-101(Cr) can act as sorbents in the composite for their high water-sorption capacity. As shown in Figure 4d, this composite exhibited greatly improved adsorption kinetics compared to pure LiCl salts with a water-sorption capacity of up to 0.77 g g−1 at 30% RH, 30 °C. This is the highest value among salt-in-MOF absorbents for sorption-based AWH. This work shows that using hygroscopic salts as absorbents encapsulated in porous MOFs contributes a lot to the sorption capacity of sorption-based AWH materials, which will help to solve water scarcity in arid regions.

4. MOF-Based Devices for Sorption-Based AWH

Besides the great efforts made to explore new MOFs with high water uptake capacity, fast adsorption kinetics, and low desorption temperature, the other equally important aspect of promoting the practical application of AWH is the design and engineering of energy-efficient water-harvesting devices and equipment. So far, several types of device prototypes have been reported based on different engineering considerations, which all showed promising results. In this section, we will briefly introduce the representative devices. Table 3 summarizes the characteristics of these devices.

4.1. Passive Water Harvesting Device

The major energy-consuming processes during an AWH adsorption-desorption cycle are heat-induced desorption and the cooling-induced condensation of the released water vapor. Therefore, to achieve minimum external electricity consumption, naturally abundant sunlight is the ideal energy source to power the heating, and ambient air is used as the heat sink for cooling. As a proof-of-concept, a box-in-box design was demonstrated with MOF-801 powder as the water sorbents [73]. The device consisted of a smaller inner box containing MOF-801 as the water sorption unit and a larger case outside for vapor condensation and enclosure (Figure 5a). The inner sorption unit box is made with acrylic and consists of a sorbent container, supporting walls and the thermal insulation compartment. Due to the low intrinsic thermal conductivity and light absorbance, MOF-801 was co-blended with 33 wt% of non-porous graphite powder, and around 1.65 kg of MOF/graphite was placed inside the container. MOF-801 required a desorption temperature inside the container of around 65 °C, while the condensation of water vapor at the wall of the outbox is at around 20 °C. To keep such a high-temperature difference within the device, thermally insulating polystyrene foam was attached around the walls, and all exposed wall surface was coated with high infrared reflectivity materials to minimize the thermal conduction and radiation toward the outer space of the container. The condensation of the vapor occurs on the inner surface of the outer enclosure case, which can constantly transfer the condensation heat toward the outside environment. Furthermore, an IR reflector was placed on the top of the case to ensure sunlight only reaches the saturated MOF layer but not heats the entire device. The system operates one full adsorption-desorption cycle per day, consisting of one adsorption half-cycle at night and one desorption half-cycle during the daytime. At night, when the relative humidity of outside air is high, the lid is opened, the humid air diffuses into the sorbent bed, and the sorption process starts. During the daytime, the lid is closed, and natural sunlight powers the heating of the sorbent bed by the solar-thermal effect. The released water vapor is subsequently condensed into droplets on the inner wall of the box and collected at the bottom. The integrated system can yield a maximum of 0.58 L kg−1 day−1 under the condition of 30% RH.
Operating one cycle per day, the water productivity of the passive device mainly depends on the maximum sorption capacity of the material. Due to the limited thermal conductivity and solar light absorbance, MOF-801 powder was co-blended with non-porous graphite into the sorbent bed, which could result in reduced mass-based water productivity. To enable passive cooling, it is required that the environment temperature is lower than the dew point of water vapor within the confined case. For an environment with surrounding temperatures higher than the dew point, an electric cooling apparatus can be used to condense the water vapor at the cost of higher energy consumption [9].

4.2. Active Water Harvesting Device

Devices operating on the passive mode have a stringent requirement on the sunlight and temperature of the environment, and the water productivity is limited by the maximum water uptake capacity of the MOF materials. However, it is not facile to develop new MOFs with extremely high water-uptake capacity, which are simultaneously easily produced in large quantities. Moreover, under practical conditions, the powdery sorbent material can hardly achieve its saturated vapor adsorption capacity, nor can it desorb water molecules completely because of the mass transfer resistance caused by the dense packing of the material and structural hindrance from the hardware.
From the operation perspective, a device that can perform multiple adsorption-desorption cycles could fundamentally circumvent the material limitation. Engineering devices that are capable of continuous operation and multiple ad-/desorption per day have been reported, in which the adsorption and desorption processes are electrically powered with fans, heaters, and condensers [37,71]. As a typical example, Hanikel et al. designed a sorption unit that can operate in an active mode (Figure 5b). The unit is comprised of sorbent beds, electric fans and heating strips, referred to as MOF exchangers. Powder-form MOF-303 are spread evenly between two layers of laminated microporous PTFE membrane and subsequently assembled into the exchanger with thermally conductive acrylic in an orthogonal configuration. The orthogonal configuration of the exchanger makes the sorption and desorption on the sorbent beds thoroughly by convection. Compared to passive mode devices, the mass transfer of the water molecules in the active systems has improved greatly. MOF-303 was chosen on account of its rapid kinetics to reach full saturation and complete desorption within a few minutes. During the adsorption, humid air was forced into the cartridge containing MOF sorbents by fans to saturate the MOF. To desorb the water, the heating strips are powered on to drive the release of water vapor from sorbent beds actively. The AWH system is constructed by connecting the MOF exchanger to a solar panel-charged battery system, a condenser, and water-collecting bottles (Figure 5c). The system can realize multiple operation cycles a day, compared to a single cycle of the passive mode device, for higher water production. With the solar module and batteries, this kind of device can perform the adsorption and desorption cycles even at night. This system could generate 1.3 L kgMOF−1 day−1 at 32% RH, more than twice the water generation value of passive devices under the same condition. In contrast to previous devices that mainly focused on the saturated sorption capacity of materials, this study demonstrated that controlling and exploiting the dynamic water capacity is an equally important aspect of high-efficiency water production.

4.3. Adaptive Water Harvesting Device

The active device requires some amount of external electricity input. Although natural sunlight could be used to drive the device’s operation, it is still desirable to further optimize the energy efficiency of the harvester in order to promote its wider applications. A new study on the improvement of freshwater production based on multiple water harvesting cycles by engineering an innovative device was reported recently, called an adaptive water harvester [75]. The design of the sorbent system is similar to the active device described above (Figure 5d), consisting of an air intake compartment, sorption compartment, and condensation compartment. Aluminum linings were used in the sorption bed packed with MOF-801 to facilitate better heat transfer. The real-time temperature and RH of the ambient environment and each part of the adaptive device is monitored by sensors. The adaptive water harvester was programmed to read the dew point from its database according to the combination of real-time temperature and RH values, and then the algorithm instructed the ad-/desorption behavior of the device in response to the dew point values. Two algorithms are developed to calculate appropriate ad-/desorption time for the adaptive device, thus optimizing the energy efficiency. The database abovementioned is set up by collecting environmental data from the active device at the condition of 7% RH to 70% RH and calculating the corresponding dew point values using the equation. Due to the real-time responsive operation of the device, this integrated system can optimize the energy efficiency of each cycle, dramatically lowering the energy consumption of sorption-based AWH technology. The adaptive device can yield 1.8 L H2O kgMOF−1 per day in the arid climate (10–30% RH) with a maximal energy consumption of 9.45 kWh, while the same device running active mode requires a 12.6 kWh power input to produce the same amount of water.

5. Conclusions and Perspective

Independent of local geographical and climatic conditions, sorption-based atmospheric water harvesting is an innovative way to achieve a decentralized freshwater supply in water-stressed regions. MOFs stand out as promising materials for their permanent porosity, adjustable chemical properties, and stable structure. MOF-based composites could simultaneously achieve improved water uptake capacity and facile regeneration, as well as realize multifunctionality through the synergy between MOF and other components. This review discusses MOFs and MOF-based composites as promising sorbent materials for moisture extraction and release, outlining the key mechanisms of vapor adsorption by MOFs with different structural types and pore sizes. Besides, the engineering considerations and operational strategies of the MOF-based water harvesting devices are discussed with passive, active and adaptive design principles.
The utilization of MOF-based sorbents in a water harvester is promising to solve water scarcity in arid regions powered by natural sunlight or other low-grade thermal resources. Significant progress has been made in both the fundamental science and practical utilization of this emerging research area of MOF-based AWH technology. However, unexplored questions and challenges remain. From the material perspective, although the pore volume and pore structure of MOFs can be tuned by adjusting metal clusters or organic ligands, their water adsorption ability, however, is still hard to predict based on reticular chemistry. More research on the water adsorption mechanisms that correlate the structure and adsorption behavior is highly needed to guide the future design and synthesis of new MOFs with higher uptake capacity and faster adsorption/desorption kinetics. In addition, large-scale production of MOFs with stable performance is still a big challenge today, which calls for more engineering exploration of a possible route for mass production. For MOF-based composite sorbents, although only a few works have been reported, they have already demonstrated great potential to improve the overall water harvesting performance. From the fundamental level, it is needed to probe how the structure of water molecules changes when diffusing in the composite absorbent during the ad-/desorption process with advanced characterization tools and simulations.
From the device perspective, the mass transfer resistance, energy efficiency, and the cost of devices are all required to be carefully evaluated when applying this technology to practice. The form of adsorbents (e.g., powder, film, bulk) and shape/structure of the sorbent unit could have a great impact on the overall mass transfer resistance of devices. However, the study merely based on isotherms of the sorbent materials does not provide direct answers. To optimize the overall energy efficiency, there is still a lot to explore regarding the choice of device material, space arrangement of each component, and operation modes. In addition, evaluation protocols and standards are needed in order to access the energy consumption of different devices more fairly. These unsolved questions require engineers and chemists to work together. The one final core target and also the greatest challenge is to transfer experimental design out of the laboratory and apply it to a productive life. We hope this review could stimulate more research effort from both chemists and engineers to further optimize current harvesting systems and look for new MOF-based sorbents.

Author Contributions

Conceptualization, Q.M. and B.W.; writing—original draft preparation, X.H. and Q.Q.; writing—review and editing, Q.M. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by National Natural Science Foundation of China, Grant No. 21625102, 21971017, and 22105021. Q.M. would like to acknowledge the funding support by the Beijing Institute of Technology Research Fund Program for Young Scholars.

Data Availability Statement

Not applicable.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Shiklomanov, I.A. Appraisal and Assessment of World Water Resources. Water Int. 2000, 25, 11–32. [Google Scholar] [CrossRef]
  2. Shiklomanov, I.A. World Freshwater Resources. Water in Crisis: A Guide to the World’s Fresh Water Resources. Clim. Chang. 1993, 45, 379–382. [Google Scholar]
  3. Mekonnen, M.M.; Hoekstra, A.Y. Four billion people facing severe water scarcity. Sci. Adv. 2016, 2, e1500323. [Google Scholar] [CrossRef] [Green Version]
  4. Wang, J.; Wang, W.; Li, J.; Mu, X.; Yan, X.; Wang, Z.; Su, J.; Lei, T.; Wang, C. Universal Strategy to Prepare a Flexible Photothermal Absorber Based on Hierarchical Fe-MOF-74 toward Highly Efficient Solar Interfacial Seawater Desalination. ACS Appl. Mater. Interfaces 2021, 13, 45944–45956. [Google Scholar] [CrossRef] [PubMed]
  5. Zhang, C.; Shi, Y.; Shi, L.; Li, H.; Li, R.; Hong, S.; Zhuo, S.; Zhang, T.; Wang, P. Designing a next generation solar crystallizer for real seawater brine treatment with zero liquid discharge. Nat. Commun. 2021, 12, 998. [Google Scholar] [CrossRef]
  6. Elimelech, M.; Phillip, W.A. The Future of Seawater Desalination: Energy, Technology, and the Environment. Science 2011, 333, 712–717. [Google Scholar] [CrossRef]
  7. Brozinski, J.M.; Lahti, M.; Meierjohann, A.; Oikari, A.; Kronberg, L. The anti-inflammatory drugs diclofenac, naproxen and ibuprofen are found in the bile of wild fish caught downstream of a wastewater treatment plant. Environ. Sci. Technol. 2013, 47, 342. [Google Scholar] [CrossRef]
  8. Hai, F.I.; Yang, S.F.; Asif, M.B.; Sencadas, V.; Shawkat, S.; Sanderson-Smith, M.; Gorman, J.; Xu, Z.; Yamamoto, K. Carbamazepine as a possible anthropogenic marker in water: Occurrences, toxicological effects, regulations and removal by wastewater treatment technologies. Water 2018, 10, 107. [Google Scholar] [CrossRef] [Green Version]
  9. Kim, H.; Yang, S.; Rao, S.R.; Narayanan, S.; Kapustin, E.A.; Furukawa, H.; Umans, A.S.; Yaghi, O.M.; Wang, E.N. Water harvesting from air with metal-organic frameworks powered by natural sunlight. Science 2017, 356, 430–432. [Google Scholar] [CrossRef] [Green Version]
  10. Zhao, F.; Zhou, X.; Liu, Y.; Shi, Y.; Dai, Y.; Yu, G. Super Moisture-Absorbent Gels for All-Weather Atmospheric Water Harvesting. Adv. Mater. 2019, 31, e1806446. [Google Scholar] [CrossRef]
  11. Bilal, M.; Sultan, M.; Morosuk, T.; Den, W.; Sajjad, U.; Aslam, M.M.A.; Shahzad, M.W.; Farooq, M. Adsorption-based atmospheric water harvesting: A review of adsorbents and systems. Int. Commun. Heat Mass Transfer. 2022, 133, 105961. [Google Scholar] [CrossRef]
  12. Fessehaye, M.; Abdul-Wahab, S.A.; Savage, M.J.; Kohler, T.; Gherezghiher, T.; Hurni, H. Fog-water collection for community use. Renew. Sustain. Energy Rev. 2014, 29, 52–62. [Google Scholar] [CrossRef]
  13. Salehi, A.A.; Ghannadi-Maragheh, M.; Torab-Mostaedi, M.; Torkaman, R.; Asadollahzadeh, M. A review on the water-energy nexus for drinking water production from humid air. Renew. Sustain. Energy Rev. 2020, 120, 109627. [Google Scholar] [CrossRef]
  14. Azeem, M.; Noman, M.T.; Wiener, J.; Petru, M.; Louda, P. Structural design of efficient fog collectors: A review. Environ. Technol. Innovation. 2020, 20, 101169. [Google Scholar] [CrossRef]
  15. Hamilton, W.J.; Seely, M.K. Fog basking by the Namib Desert beetle, Onymacris unguicularis. Nature 1976, 262, 284–285. [Google Scholar] [CrossRef]
  16. Klemm, O.; Schemenauer, R.S.; Lummerich, A.; Cereceda, P.; Marzol, V.; Corell, D.; van Heerden, J.; Reinhard, D.; Gherezghiher, T.; Olivier, J.; et al. Fog as a Fresh-Water Resource: Overview and Perspectives. AMBIO 2012, 41, 221–234. [Google Scholar] [CrossRef] [Green Version]
  17. LaPotin, A.; Kim, H.; Rao, S.R.; Wang, E.N. Adsorption-Based Atmospheric Water Harvesting: Impact of Material and Component Properties on System-Level Performance. Acc. Chem. Res. 2019, 52, 1588–1597. [Google Scholar] [CrossRef]
  18. Lee, A.; Moon, M.W.; Lim, H.; Kim, W.D.; Kim, H.Y. Water harvest via dewing. Langmuir 2012, 28, 10183–10191. [Google Scholar] [CrossRef]
  19. Hanikel, N.; Prevot, M.S.; Yaghi, O.M. MOF water harvesters. Nat. Nanotechnol. 2020, 15, 348–355. [Google Scholar] [CrossRef]
  20. Ejeian, M.; Wang, R.Z. Adsorption-based atmospheric water harvesting. Joule 2021, 5, 1678–1703. [Google Scholar] [CrossRef]
  21. Elmer, T.H.; Hyde, J.F. Recovery of Water from Atmospheric Air in Arid Climates. Sep. Sci. Technol. 1986, 21, 251–266. [Google Scholar] [CrossRef]
  22. Heidari, A.; Roshandel, R.; Vakiloroaya, V. An innovative solar assisted desiccant-based evaporative cooling system for co-production of water and cooling in hot and humid climates. Energy Convers. Manag. 2019, 185, 396–409. [Google Scholar] [CrossRef]
  23. Ge, T.S.; Dai, Y.J.; Wang, R.Z.; Peng, Z.Z. Experimental comparison and analysis on silica gel and polymer coated fin-tube heat exchangers. Energy 2010, 35, 2893–2900. [Google Scholar] [CrossRef]
  24. Jänchen, J.; Ackermann, D.; Stach, H.; Brösicke, W. Studies of the water adsorption on Zeolites and modified mesoporous materials for seasonal storage of solar heat. Sol. Energy 2004, 76, 339–344. [Google Scholar] [CrossRef]
  25. Zhou, X.; Lu, H.; Zhao, F.; Yu, G. Atmospheric Water Harvesting: A Review of Material and Structural Designs. ACS Mater. Lett. 2020, 2, 671–684. [Google Scholar] [CrossRef]
  26. Barreneche, C.; Fernández, A.I.; Cabeza, L.F.; Cuypers, R. Thermophysical Characterization of Sorption TCM. Energy Procedia 2014, 48, 273–279. [Google Scholar] [CrossRef] [Green Version]
  27. Sögütoglu, L.C.; Steiger, M.; Houben, J.; Biemans, D.; Fischer, H.R.; Donkers, P.; Huinink, H.; Adan, O.C.G. Understanding the Hydration Process of Salts: The Impact of a Nucleation Barrier. Cryst. Growth Des. 2019, 19, 2279–2288. [Google Scholar] [CrossRef]
  28. Li, R.; Shi, Y.; Shi, L.; Alsaedi, M.; Wang, P. Harvesting Water from Air: Using Anhydrous Salt with Sunlight. Environ. Sci. Technol. 2018, 52, 5398–5406. [Google Scholar] [CrossRef] [PubMed]
  29. Kallenberger, P.A.; Fröba, M. Water harvesting from air with a hygroscopic salt in a hydrogel–derived matrix. Commun. Chem. 2018, 1, 28. [Google Scholar] [CrossRef] [Green Version]
  30. Furukawa, H.; Cordova, K.E.; O’Keeffe, M.; Yaghi, O.M. The chemistry and applications of metal-organic frameworks. Science 2013, 341, 1230444. [Google Scholar] [CrossRef] [Green Version]
  31. Yaghi, O.M.; O’Keeffe, M.; Ockwig, N.W.; Chae, H.K.; Eddaoudi, M.; Kim, J. Reticular synthesis and the design of new materials. Nature 2003, 423, 705–714. [Google Scholar] [CrossRef] [PubMed]
  32. Cao, Y.; Chen, X.; Li, X.; Wang, B. Tuning Surface Functionalization and Pore Structure of UiO-66 Metal–Organic Framework Nanoparticles for Organic Pollutant Elimination. ACS Appl. Nano Mater. 2021, 4, 5486–5495. [Google Scholar] [CrossRef]
  33. Chen, L.; Hao, Y.; Guo, Y.; Zhang, Q.; Li, J.; Gao, W.; Ren, L.; Su, X.; Hu, L.; Zhang, N.; et al. Metal–Organic Framework Membranes Encapsulating Gold Nanoparticles for Direct Plasmonic Photocatalytic Nitrogen Fixation. J. Am. Chem. Soc. 2021, 143, 5727–5736. [Google Scholar] [CrossRef]
  34. Liu, Y.; Li, S.; Dai, L.; Li, J.; Lv, J.; Zhu, Z.; Yin, A.; Li, P.; Wang, B. The Synthesis of Hexaazatrinaphthylene-Based 2D Conjugated Copper Metal-Organic Framework for Highly Selective and Stable Electroreduction of CO2 to Methane. Angew. Chem. Int. Ed. 2021, 60, 16409–16415. [Google Scholar] [CrossRef] [PubMed]
  35. Gao, X.; Li, S.; Du, Y.; Wang, B. A ZIF-67-derived–sulfur sandwich structure for high performance Li–S batteries. APL Mater. 2019, 7, 091115. [Google Scholar] [CrossRef]
  36. Chen, Z.; Wang, X.; Islamoglu, T.; Farha, O.K. Green Synthesis of a Functionalized Zirconium-Based Metal–Organic Framework for Water and Ethanol Adsorption. Inorganics 2019, 7, 56. [Google Scholar] [CrossRef] [Green Version]
  37. Hanikel, N.; Prevot, M.S.; Fathieh, F.; Kapustin, E.A.; Lyu, H.; Wang, H.; Diercks, N.J.; Glover, T.G.; Yaghi, O.M. Rapid Cycling and Exceptional Yield in a Metal-Organic Framework Water Harvester. ACS Cent. Sci. 2019, 5, 1699–1706. [Google Scholar] [CrossRef]
  38. Logan, M.W.; Langevin, S.; Xia, Z. Reversible Atmospheric Water Harvesting Using Metal-Organic Frameworks. Sci. Rep. 2020, 10, 1492. [Google Scholar] [CrossRef] [Green Version]
  39. Lenzen, D.; Bendix, P.; Reinsch, H.; Frohlich, D.; Kummer, H.; Mollers, M.; Hugenell, P.P.C.; Glaser, R.; Henninger, S.; Stock, N. Scalable Green Synthesis and Full-Scale Test of the Metal-Organic Framework CAU-10-H for Use in Adsorption-Driven Chillers. Adv. Mater. 2018, 30, 1705869. [Google Scholar] [CrossRef]
  40. Furukawa, H.; Gandara, F.; Zhang, Y.B.; Jiang, J.; Queen, W.L.; Hudson, M.R.; Yaghi, O.M. Water adsorption in porous metal-organic frameworks and related materials. J. Am. Chem. Soc. 2014, 136, 4369–4381. [Google Scholar] [CrossRef]
  41. Lu, Z.; Duan, J.; Du, L.; Liu, Q.; Schweitzer, N.M.; Hupp, J.T. Incorporation of free halide ions stabilizes metal–organic frameworks (MOFs) against pore collapse and renders large-pore Zr-MOFs functional for water harvesting. J. Mater. Chem. A 2022, 10, 6442–6447. [Google Scholar] [CrossRef]
  42. Fröhlich, D.; Pantatosaki, E.; Kolokathis, P.D.; Markey, K.; Reinsch, H.; Baumgartner, M.; van der Veen, M.A.; De Vos, D.E.; Stock, N.; Papadopoulos, G.K.; et al. Water adsorption behaviour of CAU-10-H: A thorough investigation of its structure–property relationships. J. Mater. Chem. A 2016, 4, 11859–11869. [Google Scholar] [CrossRef] [Green Version]
  43. Canivet, J.; Bonnefoy, J.; Daniel, C.; Legrand, A.; Coasne, B.; Farrusseng, D. Structure–property relationships of water adsorption in metal–organic frameworks. New J. Chem. 2014, 38, 3102–3111. [Google Scholar] [CrossRef]
  44. Liu, J.; Wang, Y.; Benin, A.I.; Jakubczak, P.; Willis, R.R.; LeVan, M.D. CO2/H2O adsorption equilibrium and rates on metal-organic frameworks: HKUST-1 and Ni/DOBDC. Langmuir 2010, 26, 14301–14307. [Google Scholar] [CrossRef]
  45. Hanikel, N.; Pei, X.; Chheda, S.; Lyu, H.; Jeong, W.; Sauer, J.; Gagliardi, L.; Yaghi, O.M. Evolution of water structures in metal-organic frameworks for improved atmospheric water harvesting. Science 2021, 374, 454–459. [Google Scholar] [CrossRef]
  46. Cmarik, G.E.; Kim, M.; Cohen, S.M.; Walton, K.S. Tuning the adsorption properties of UiO-66 via ligand functionalization. Langmuir 2012, 28, 15606–15613. [Google Scholar] [CrossRef]
  47. Schoenecker, P.M.; Carson, C.G.; Jasuja, H.; Flemming, C.J.J.; Walton, K.S. Effect of Water Adsorption on Retention of Structure and Surface Area of Metal–Organic Frameworks. Ind. Eng. Chem. Res. 2012, 51, 6513–6519. [Google Scholar] [CrossRef]
  48. Ko, N.; Choi, P.G.; Hong, J.; Yeo, M.; Sung, S.; Cordova, K.E.; Park, H.J.; Yang, J.K.; Kim, J. Tailoring the water adsorption properties of MIL-101 metal–organic frameworks by partial functionalization. J. Mater. Chem. A 2015, 3, 2057–2064. [Google Scholar] [CrossRef]
  49. Towsif Abtab, S.M.; Alezi, D.; Bhatt, P.M.; Shkurenko, A.; Belmabkhout, Y.; Aggarwal, H.; Weseliński, Ł.J.; Alsadun, N.; Samin, U.; Hedhili, M.N.; et al. Reticular Chemistry in Action: A Hydrolytically Stable MOF Capturing Twice Its Weight in Adsorbed Water. Chem 2018, 4, 94–105. [Google Scholar] [CrossRef] [Green Version]
  50. Drisdell, W.S.; Poloni, R.; McDonald, T.M.; Long, J.R.; Smit, B.; Neaton, J.B.; Prendergast, D.; Kortright, J.B. Probing adsorption interactions in metal-organic frameworks using X-ray spectroscopy. J. Am. Chem. Soc. 2013, 135, 18183–18190. [Google Scholar] [CrossRef]
  51. Dietzel, P.D.; Johnsen, R.E.; Blom, R.; Fjellvag, H. Structural changes and coordinatively unsaturated metal atoms on dehydration of honeycomb analogous microporous metal-organic frameworks. Chemistry 2008, 14, 2389–2397. [Google Scholar] [CrossRef] [PubMed]
  52. Kalmutzki, M.J.; Diercks, C.S.; Yaghi, O.M. Metal-Organic Frameworks for Water Harvesting from Air. Adv. Mater. 2018, 30, e1704304. [Google Scholar] [CrossRef] [PubMed]
  53. Shi, W.; Guan, W.; Lei, C.; Yu, G. Sorbents for Atmospheric Water Harvesting: From Design Principles to Applications. Angew. Chem. Int. Ed. 2022, 61, e202211267. [Google Scholar] [CrossRef] [PubMed]
  54. Jeremias, F.; Khutia, A.; Henninger, S.K.; Janiak, C. MIL-100(Al, Fe) as water adsorbents for heat transformation purposes—A promising application. J. Mater. Chem. 2012, 22, 10148–10151. [Google Scholar] [CrossRef]
  55. Akiyama, G.; Matsuda, R.; Sato, H.; Hori, A.; Takata, M.; Kitagawa, S. Effect of functional groups in MIL-101 on water sorption behavior. Microporous Mesoporous Mater. 2012, 157, 89–93. [Google Scholar] [CrossRef]
  56. Xu, J.; Li, T.; Chao, J.; Wu, S.; Yan, T.; Li, W.; Cao, B.; Wang, R. Efficient Solar-Driven Water Harvesting from Arid Air with Metal-Organic Frameworks Modified by Hygroscopic Salt. Angew. Chem. Int. Ed. 2020, 59, 5202–5210. [Google Scholar] [CrossRef]
  57. Permyakova, A.; Wang, S.; Courbon, E.; Nouar, F.; Heymans, N.; D’Ans, P.; Barrier, N.; Billemont, P.; De Weireld, G.; Steunou, N.; et al. Design of salt–metal organic framework composites for seasonal heat storage applications. J. Mater. Chem. A 2017, 5, 12889–12898. [Google Scholar] [CrossRef]
  58. Garzón-Tovar, L.; Pérez-Carvajal, J.; Imaz, I.; Maspoch, D. Composite Salt in Porous Metal-Organic Frameworks for Adsorption Heat Transformation. Adv. Funct. Mater. 2017, 27, 1606424. [Google Scholar] [CrossRef] [Green Version]
  59. Zhang, Y.; Wu, L.; Wang, X.; Yu, J.; Ding, B. Super hygroscopic nanofibrous membrane-based moisture pump for solar-driven indoor dehumidification. Nat. Commun. 2020, 11, 3302. [Google Scholar] [CrossRef]
  60. Yilmaz, G.; Meng, F.L.; Lu, W.; Abed, J.; Peh, C.K.N.; Gao, M.; Sargent, E.H.; Ho, G.W. Autonomous atmospheric water seeping MOF matrix. Sci. Adv. 2020, 6, 2375–2548. [Google Scholar] [CrossRef]
  61. Karmakar, A.; Mileo, P.G.M.; Bok, I.; Peh, S.B.; Zhang, J.; Yuan, H.; Maurin, G.; Zhao, D. Thermo-Responsive MOF/Polymer Composites for Temperature-Mediated Water Capture and Release. Angew. Chem. Int. Ed. 2020, 59, 11003–11009. [Google Scholar] [CrossRef] [PubMed]
  62. Yan, J.; Yu, Y.; Ma, C.; Xiao, J.; Xia, Q.; Li, Y.; Li, Z. Adsorption isotherms and kinetics of water vapor on novel adsorbents MIL-101(Cr)@GO with super-high capacity. Appl. Therm. Eng. 2015, 84, 118–125. [Google Scholar] [CrossRef]
  63. Li, A.; Xiong, J.; Liu, Y.; Wang, L.; Qin, X.; Yu, J. A Rapid-Ab/Desorption and Portable Photothermal MIL-101(Cr) Nanofibrous Composite Membrane Fabricated by Spray-Electrospinning for Atmosphere Water Harvesting. Energy Environ. Mater. 2022, 12254. [Google Scholar] [CrossRef]
  64. Laha, S.; Maji, T.K. Binary/Ternary MOF Nanocomposites for Multi-Environment Indoor Atmospheric Water Harvesting. Adv. Funct. Mater. 2022, 32, 2203093. [Google Scholar] [CrossRef]
  65. Wickenheisser, M.; Paul, T.; Janiak, C. Prospects of monolithic MIL-MOF@poly(NIPAM)HIPE composites as water sorption materials. Microporous Mesoporous Mater. 2016, 220, 258–269. [Google Scholar] [CrossRef]
  66. Ehrenmann, J.; Henninger, S.K.; Janiak, C. Water Adsorption Characteristics of MIL-101 for Heat-Transformation Applications of MOFs. Eur. J. Inorg. Chem. 2010, 2011, 471–474. [Google Scholar] [CrossRef]
  67. Tao, Y.; Wu, Q.; Huang, C.; Su, W.; Ying, Y.; Zhu, D.; Li, H. Sandwich-Structured Carbon Paper/Metal-Organic Framework Monoliths for Flexible Solar-Powered Atmospheric Water Harvesting On Demand. ACS Appl. Mater. Interfaces 2022, 14, 10966–10975. [Google Scholar] [CrossRef]
  68. Li, Q.; Ying, Y.; Tao, Y.; Li, H. Assemblable Carbon Fiber/Metal–Organic Framework Monoliths for Energy-Efficient Atmospheric Water Harvesting. Ind. Eng. Chem. Res. 2022, 61, 1344–1354. [Google Scholar] [CrossRef]
  69. Yang, K.; Shi, Y.; Wu, M.; Wang, W.; Jin, Y.; Li, R.; Shahzad, M.W.; Ng, K.C.; Wang, P. Hollow spherical SiO2 micro-container encapsulation of LiCl for high-performance simultaneous heat reallocation and seawater desalination. J. Mater. Chem. A 2020, 8, 1887–1895. [Google Scholar] [CrossRef] [Green Version]
  70. Li, R.; Shi, Y.; Alsaedi, M.; Wu, M.; Shi, L.; Wang, P. Hybrid Hydrogel with High Water Vapor Harvesting Capacity for Deployable Solar-Driven Atmospheric Water Generator. Environ. Sci. Technol. 2018, 52, 11367–11377. [Google Scholar] [CrossRef]
  71. Li, R.; Shi, Y.; Wu, M.; Hong, S.; Wang, P. Improving atmospheric water production yield: Enabling multiple water harvesting cycles with nano sorbent. Nano Energy 2020, 67, 104255. [Google Scholar] [CrossRef]
  72. Song, Y.; Xu, N.; Liu, G.; Qi, H.; Zhao, W.; Zhu, B.; Zhou, L.; Zhu, J. High-yield solar-driven atmospheric water harvesting of metal-organic-framework-derived nanoporous carbon with fast-diffusion water channels. Nat. Nanotechnol. 2022, 17, 857–863. [Google Scholar] [CrossRef]
  73. Fathieh, F.; Kalmutzki, M.J.; Kapustin, E.A.; Waller, P.J.; Yang, J.; Yaghi, O.M. Practical water production from desert air. Sci. Adv. 2018, 4, eaat3198. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  74. Kim, H.; Rao, S.R.; Kapustin, E.A.; Zhao, L.; Yang, S.; Yaghi, O.M.; Wang, E.N. Adsorption-based atmospheric water harvesting device for arid climates. Nat. Commun. 2018, 9, 1191. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  75. Almassad, H.A.; Abaza, R.I.; Siwwan, L.; Al-Maythalony, B.; Cordova, K.E. Environmentally adaptive MOF-based device enables continuous self-optimizing atmospheric water harvesting. Nat. Commun. 2022, 13, 4873. [Google Scholar] [CrossRef] [PubMed]
Water 14 03487 g001 550
Figure 1. Schematic illustration of the working process of sorption-based atmospheric water harvesting.
Figure 1. Schematic illustration of the working process of sorption-based atmospheric water harvesting.
Water 14 03487 g001
Water 14 03487 g002 550
Figure 2. (a) Thermal ellipsoids of the different water molecules in the framework. Inset: DFT result of the open metal site. (b) The adsorption isotherms of MOF-74(Mg) and MOF-74(Ni). (c) Schematic illustration of different sorption sites of MOF-303 in the pore-filling process. (d) The adsorption isotherms of MOF-303. (e) Water molecules cluster in the cubic cages of Cr-soc-MOF-1. (f) The adsorption isotherms of Cr-soc-MOF-1.
Figure 2. (a) Thermal ellipsoids of the different water molecules in the framework. Inset: DFT result of the open metal site. (b) The adsorption isotherms of MOF-74(Mg) and MOF-74(Ni). (c) Schematic illustration of different sorption sites of MOF-303 in the pore-filling process. (d) The adsorption isotherms of MOF-303. (e) Water molecules cluster in the cubic cages of Cr-soc-MOF-1. (f) The adsorption isotherms of Cr-soc-MOF-1.
Water 14 03487 g002
Water 14 03487 g003 550
Figure 3. (a) Schematic illustration of the polymer-in-MOF composites and the temperature-triggered water capture and release process. (b) Comparison of adsorption isotherm curves of composites loaded with different amounts of PNIPAM. (c) Comparison of water uptake capacity in different environments.
Figure 3. (a) Schematic illustration of the polymer-in-MOF composites and the temperature-triggered water capture and release process. (b) Comparison of adsorption isotherm curves of composites loaded with different amounts of PNIPAM. (c) Comparison of water uptake capacity in different environments.
Water 14 03487 g003
Water 14 03487 g004 550
Figure 4. (a) SEM image and elemental mapping of CaCl2-in-UIO-66. (b) Adsorption isotherms of CaCl2 (green), CaCl2-in-UIO-66 (blue) and UIO-66 (red). (c) Schematic illustration of a LiCl-in-MIL-101(Cr) and its AHW process. (d) Adsorption isotherm of LiCl-in-MIL-101(Cr).
Figure 4. (a) SEM image and elemental mapping of CaCl2-in-UIO-66. (b) Adsorption isotherms of CaCl2 (green), CaCl2-in-UIO-66 (blue) and UIO-66 (red). (c) Schematic illustration of a LiCl-in-MIL-101(Cr) and its AHW process. (d) Adsorption isotherm of LiCl-in-MIL-101(Cr).
Water 14 03487 g004
Water 14 03487 g005 550
Figure 5. (a) Schematic illustrations of the integrated system of the passive device. (b) the active device. (c) the photo of the device prototype operating in active mode. (d) schematic illustrations of the adaptive device.
Figure 5. (a) Schematic illustrations of the integrated system of the passive device. (b) the active device. (c) the photo of the device prototype operating in active mode. (d) schematic illustrations of the adaptive device.
Water 14 03487 g005
Table
Table 1. MOFs used for sorption-based AWH.
Table 1. MOFs used for sorption-based AWH.
MOF SorbentsLinkerBET (m2 g−1)Inflection Point (P/P0)Sorption Capacity (P/P0 = 0.9)/g g−1Ref.
CAU-10-Hm-BDC6000.30.36[39,42]
UIO-66(NH2)(NH2)BDC11230.20.38[43]
(Ni)MOF-74DOBDC80000.53[44]
MOF-303HPDC13350.10.44[45]
(Al)MIL-53BDC10400.10.09[43]
MOF-801Fumarate9900.070.45[40]
UIO-66BDC11050.250.44[46]
(Mg)MOF-74DOT125000.75[47]
(Cr)MIL-101(NH2)(NH2)BDC17900.360.83[43]
(Cr)MIL-101BDC30700.41.29[48]
(Cr)MOF-1TCPT45490.581.95[49]
Table
Table 2. Summary of MOF-based composites for ABAWH.
Table 2. Summary of MOF-based composites for ABAWH.
MOF-Based CompositesFunctions of Each ComponentSorption Capacity
(g g−1)		Ref.
LiCl@MIL-101(Cr)LiCl: absorber;
MIL-101(Cr): supporting matrix.		0.8 (30% RH)[56]
CaCl2@MIL-101(Cr)CaCl2: absorber;
MIL-101(Cr): supporting matrix.		0.60 (30% RH)[57]
CaCl2@UiO-66CaCl2: absorber;
UIO-66: supporting matrix.		0.67 (30% RH)[58]
PAN/MIL@LiCl-PAN/CB PAN: forming substrate membrane with MIL-101(Cr) and CNTs;
MIL-101(Cr): absorber;
LiCl: absorber;
CB: photothermal conversion.		3.01 (90% RH)[59]
PNIPAM@MIL-101(Cr)PNIPAM: supporting matrix;
MIL-101(Cr): absorber.		6.39 (90% RH)[60]
MIL-101(Cr)@PNIPAMMIL-101(Cr): supporting matrix, absorbent;
PNIPAM: promoting facile regeneration.		4.4 (96% RH)[61]
MIL-101(Cr)@GOMIL-101(Cr): absorber;
GO: enhancing water sorption.		1.58 (70% RH)[62]
MIL-101(Cr)/PAN/CNTsMIL-101(Cr): absorber;
PAN: forming substrate membrane with CNTs;
CNTs: photothermal conversion.		1.04 (98%RH)[63]
CuBTC/AC/GOCuBTC: absorber;
AC: enhancing the stability of composite;
GO: thermal conductivity.		0.67 (90%RH)[64]
Table
Table 3. Summary of MOF-based devices for ABAWH.
Table 3. Summary of MOF-based devices for ABAWH.
Device TypeConfigurationSorbentsWater Productivity
(L kgMOF−1 day−1)		CharacteristicsRef.
passiveAdsorption and condenser chamber, test apparatus.MOF-8010.25 (20% RH)
  • one adsorption half-cycle at night and one desorption half-cycle during the daytime;
  • desorb directly only using solar energy;
  • used air as the heat sink.
[73]
The sorption unit, condenser case.MOF-801/nonporous graphite0.1 (5–40% RH)[9]
activeMOF exchanger, compressor-based condenser, solar cell.MOF-3030.7 (10–30% RH)
1.3 (40–60% RH)
  • multiple ad-/desorption cycles a day;
  • photovoltaic power generation;
  • blows the air with fans
[37]
MOF layer, solar simulator, acrylic enclosure, and condenser.MOF-8012.8 (20% RH)
  • multiple ad-/desorption cycles a day;
  • solar simulator helps to desorb
  • 3. monitor and keep the ambient temperature constant with thermocouples
[74]
adaptiveAir intake compartment, sorption compartment, condensation compartmentMOF-8011.8 (10–30% RH)
3.52 (40–60% RH)
  • multiple ad-/desorption cycles a day;
  • monitor the environment in real time;
  • respond to the real-time data to save energy
[75]
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Huang, X.; Qin, Q.; Ma, Q.; Wang, B. Atmospheric Water Harvesting with Metal-Organic Frameworks and Their Composites: From Materials to Devices. Water 2022, 14, 3487. https://doi.org/10.3390/w14213487

AMA Style

Huang X, Qin Q, Ma Q, Wang B. Atmospheric Water Harvesting with Metal-Organic Frameworks and Their Composites: From Materials to Devices. Water. 2022; 14(21):3487. https://doi.org/10.3390/w14213487

Chicago/Turabian Style

Huang, Xiuying, Qin Qin, Qinglang Ma, and Bo Wang. 2022. "Atmospheric Water Harvesting with Metal-Organic Frameworks and Their Composites: From Materials to Devices" Water 14, no. 21: 3487. https://doi.org/10.3390/w14213487

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop